Controlled peel for a defined removal window
Product codeFL-5068
Removable Film Adhesive
Water-based removable adhesive for protective film, removable labels and temporary positioning where peel growth and residue must be checked under real use conditions.
Application fit highlights
Why evaluate FL-5068 for your application
Peel-growth and residue screening on the actual surface
Coating trials matched to film, coat weight and line conditions
Application risks
Problems to check before bulk production
Edge lift after application
PE and PP films can be difficult to wet. Film treatment, coat weight and the protected surface should be checked together.
Peel rises during storage
A construction that removes cleanly after one hour may behave differently after days of dwell, heat or stacking pressure.
Residue criteria are unclear
Removal claims need a defined surface, dwell time, temperature, peel angle and acceptance method.
Coating looks stable but conversion fails
Foam, leveling, film anchorage and drying can affect the finished roll even when initial tack appears acceptable.
What this product is for
FL-5068 is positioned for removable protective film, film labels and positioning tapes where the buyer needs enough hold during use and controlled removal after a defined dwell time. The trial is judged on the final construction, not on adhesive data alone.
This page is written for application screening and sample discussion. Final performance should be confirmed with the buyer's substrate, process route, test method and acceptance standard.
Suitable applications
- Protective film
- Removable film labels
- Positioning tapes
- Temporary surface protection
Suitable substrates
PET and BOPP filmPE and PP filmCoated plastic surfacesCoated metal surfaces
Screening information
Only application-facing screening information is listed here. Detailed ranges and final product data should be confirmed by TDS and sample testing.
Product familyWater-based acrylic pressure sensitive adhesive
Application directionProtective film, removable film labels, temporary labels
SubstratesPET, BOPP, PE and PP film with the actual protected plastic, coated or metal surface tested separately
Data boundaryTypical range only; final data should be confirmed by TDS and sample testing
Process notes and first trial checks
Confirm film type, coating side, protected surface and dry coat weight before comparing peel behavior.
Run removal checks after short dwell and aged dwell conditions because peel growth can change the recommendation.
Record removal speed, removal angle, temperature and storage condition when checking residue.
Inspect film anchorage, edge lift, residue and surface marking before approving a production roll.
Frequently asked questions
What applications is FL-5068 Water-Based Removable Film Adhesive suitable for?
FL-5068 Water-Based Removable Film Adhesive is positioned for Protective film, Removable film labels, Positioning tapes, Temporary surface protection. Final suitability should be confirmed with the buyer's substrate, process and test method.
What information is needed before requesting a sample or quote?
Please provide substrate, surface treatment, coating or bonding method, drying or pressing condition, current failure mode, target test and required documents.
Can Mengze provide TDS or SDS?
TDS or SDS support can be provided after the application route and document need are confirmed.
Common failure modes
- Adhesive residue after removal
- Peel growth after dwell time or heat aging
- Poor wet-out on low-surface-energy film or textured surfaces
- Surface mark or damage on sensitive coated substrates
Sample request checklist
- Film type and thickness
- Protected surface or label surface
- Target peel range and removal window
- Dwell-time and aging test condition
- Residue and protected-surface acceptance method
- Coating equipment, coat weight and drying window
Related product comparison
Use FL-4561 when the film label needs stronger holding while removability still requires dwell-time evaluation.Use AC-5309H or AC-5406 when the project moves toward stronger permanent bonding or higher tack.
Testing disclaimer
Removability depends on film, protected surface, surface treatment, coat weight, dwell time, temperature and removal method. Final approval should use the buyer's finished construction and agreed acceptance test.
Related applications
Protective Film Adhesive
Protective film adhesive selection depends on film type, protected surface, dwell time, storage environment and removal method.
Film Label Adhesive
Film label adhesive selection should match facestock, liner, coating method, target surface, aging condition and the required balance between holding and removability.
Related technical resources
How to Test Protective Film Adhesive Residue
Protective film residue testing should use the real protected surface, defined dwell time, removal method and visual acceptance standard.
Why Removable Adhesives Need Dwell-Time Testing
A removable adhesive can look acceptable in a short test and still change after storage, heat exposure or long dwell time on the final surface.
Related products
Request sample, quote or TDS
Send your substrate, coating method, current bonding problem and target test method. We can suggest a sample route before sharing detailed TDS or SDS.
Include these details
- Film type and thickness
- Protected surface or label surface
- Target peel range and removal window
- Dwell-time and aging test condition
- Residue and protected-surface acceptance method